Top products
MAX7219 Dot Matrix Module For Arduino Microcontroller 4 In One Display with 5P Line
close

Bridge Rectifier KBPC2510 25A 1000V
close

RFID / Keypad Entry Lock Door Access Controller System
close

aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()

63V Boost /Step up Configured Lm2577 Module with Heat sink
close

Input voltage range: 3.5V-35V ( must ensure that the set output voltage is higher than the input voltage )

Output voltage range: 5.0V-56V

Input maximum current: 3A

Input continuous working current: 2A (good ventilation and heat dissipation conditions, the ratio of output voltage to input voltage cannot be greater than 3)

Appearance size: length * width * height 4.3cm * 3.0cm * 1.2cm

2A Dual, Power Bank Circuit with LCD battery Status display
close

Note: B+ and B- of the boosted battery must not be reversed.

Application: All 3.7-4.2V rechargeable lithium batteries, such as mobile phone battery flat battery 18650 battery and so on!

Can be connected to a lithium battery or parallel multi-cell lithium battery

Lithium battery positive electrode connected to B+      lithium battery negative electrode connected to B-

Attention!!!

Note: B+ and B- of the boosted battery must not be reversed.

The first use requires a Micro USB port to activate once

Tips: This shop has a large number of lithium batteries for sale, you can buy them together! !

 Charging indication: the charging display will show the IN letter

Output load indication: long press the LED light button after the load is turned on, the output starts, the display will show the OUT letter and the relative output voltage and current 5V1A or 5V2.1A

Protection function: The protection circuit of the boosted lithium battery has been integrated to prevent over-discharge, over-charge and overload.

Note: B+ and B- of the boosted battery must not be reversed.

Can be connected to a lithium battery or parallel multi-cell lithium battery

Lithium battery positive electrode connected to B+ lithium battery negative electrode connected to B-

Attention!!!

The first time you need to activate the Micro USB port, you will charge it for 1 minute before using it.

Peel Pay Sheet for Vacuum baging
close

This Peel pay sheet is used in the vacuum baging process, it helps to release the infusing mesh/net easly when the epoxy get hard /cure .  you can see the easy composit video in youtube for better understanding of this material.

Laser Range Finder With Angle and Height
close

 

 

 

75C 3S OCDAY 1500mAh 11.1V lipo battery Highest Quality
close

This 11.1V 1500mAh 75C 3S lipo battery is designed for 150-280 racing quadcopter RC super fans. With high discharge rate ability, it can let the drone get more strong power to take off and speed up. If you love your RC drone, it will be a good and economical choice.

Weight: 150 grams




Features:
Easy to install
Rechargeable battery
Light weight and portable to carry
Large battery capacity can support longer working time
Environmental friendly packaging material
Stable output current, protect your RC model
High discharge rate provide more strong power for your drone
11.1V 1500mAh 75C 3S lipo Battery with XT60 plug
Suitable for RC 150-280 racing quadcopter drone

Specifications:
Brand: OCDAY
Model: VMHT16130
Battery capacity: 1500mAh
Discharge rate: 75C
Battery section: 3S (11.1V)
Charge Plug: 4 pin balance connector
Discharge Plug: XT60
Suitable drone: 150-280 racing quadcopter like QAV180 QAV250 ZMR250
Dimension: 74 * 34 * 29mm (deviation due to manual measurement)
Weight: 140g

Package Information:
Package size: 12.7 * 5.7 * 5.5cm / 5 * 2.2 * 2.2in
Package weight: 177g / 6.2oz
General box package

Caution for the battery:
Don't over-charge, or over-discharge batteries.
Don't put it beside the high temperature condition.
Don't throw it into fire.
Don't throw it into water.


Package List:
1 * OCDAY 11.1V 1500mAh 75C Li-Po Battery (XT60 Plug)
1 * Battery Tape
1 * English Manual

75C 4S 1300mAh 14.8V lipo battery High Quality
close

Weight: 180 grams

32*26cm PCB Milling 3 axis CNC Machine with Driver
close

Courier charges will be decided later after confirmation from TCS

Features:

           Structure: 2040 aluminum Strip for X-axis and Y-axis travel

           Bed Size: 26 cm and 32 cm

            Spindle Power: 90W

            Spindle Diameter: 41mm

           Height (Z-axis travel):  4.5 cm

           Z-axis Rail: 8MM 

           Bearing: linear bearings

           Screw : T8 stainless steel screw, double nuts tolerance,

           Compatibility: CNC and laser can be installed.
         
           Stepper Motor:  N
ew High-Quality stepper motor (NEMA 17)

           Interface: USB

           Spindle Motor Speed: Variable

           Software Support: GRBL

           Recommended Software for PCB to G Code: FlateCam