Computer Interface
ENC28J60 ETHERNET LAN MODULE
close

The ENC28J60 Ethernet Module utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20MHz.

 

FT232RL usb to serial (usb-serial) converter module
close

Description: Very low-cost way to add USB capability to an Arduino or other microcontroller. Use to give your own breadboard Arduino USB capability for bootloading or downloading sketches. Note: this board includes a DTR pin needed to auto-reset Arduino when downloading to your device.

Product Description: Very low-cost way to add USB capability to an Arduino or other microcontroller. Use to give your own breadboard Arduino USB capability for bootloading or downloading sketches. Note: this board includes a DTR pin needed to auto-reset Arduino when downloading to your device. Use FT232RL chip Draw out all signal port of FT232RL chip RXD/TXD transceiver communication indicator USB power supply can be set to 5V or 3.3V , set by solder pad Includes over-current protection, using a 500ma self-restoring fuse Use new design, converte USB into serial port.

USB to RS232 (usb-rs232) Converter Cable
close

The USB to Serial Adapter Cable lets you connect DB9 RS232 serial devices to your Mac or PC laptop or desktop computer through an available USB port, as though the computer offered an onboard DB9M connector.  Simple to install and use, this USB to Serial adapter provides a cost-effective solution that bridges the compatibility gap between modern computers and legacy serial peripherals.

Features:
USB specification 1.1 & 2.0 compliant
Supports RS232 serial interface DB9 male
Supports over 1 Mbps data transfer rate
Supports remote wake-up and power management
Supports Win98/2000/XP/MAC OS v8.6 or Higher/Vista

10PIN to 6PIN ISP Adapter Board Adapter Converter Board Module
close

Description:

1. the standard ATMEL ISP10 converted into standard ISP6

2. used to AT89S5x series microcontroller download interface switching

3. used to AVR series MCU download interface switching
 
4. Arduino firmware burn write interface switching

Package Included:

1 X 10PIN to 6PIN ISP Adapter Board

LoRa32u4 II Lora Development Board Module LiPo Atmega328 SX1276 HPD13 868MHZ with Antenna
close

Description:
LoRa32u4 II is a light and low consumption board based on the Atmega32u4 and HPD13  868MHz LoRA module and an USB battery charging circuit. Ideal for creating long range wireless networks that can exceed 2.4 GHz 802.15.4 and similar, it is more flexible than Bluetooth LE, does not require high power unlike WiFi and offers long range.
 
The ATmega32u4 is clocked at 8 MHz and 3.3 V. This chip has 32 K of flash, 2 K of RAM and built-in USB to Serial communication, debugging and programming capabilities without the need for an external FTDI chip, it can also act as an HID device (mouse, keyboard, USB MIDI device, etc).
This board is also equipped with a LiPo and Liion charging circuit and a standard battery interface. It is fully compatible with Arduino. A white user led is tied to pin 13. An orange LED is used for charging status.

HPD13 wireless module, using high-performance, highly integrated RF transceiver chip SX1276 design. Advanced LoRaTM spread spectrum communication technology to ensure that the module communication distance and anti-jamming capability greatly improved, and also achieved a very low current consumption. In the LoRaTM mode, the HPD13 provides higher reception sensitivity performance, more robust anti-jamming capability, and improved communication distance and reliability compared to the same transmit and receive modules on the market. In normal (G) FSK mode, it also provides industry-specific receiver sensitivity, as well as very high communication rates.  


ATmega32u4 @ 8MHz with 3.3V logic/power
3.3V regulator with 500mA peak current output
USB native support, comes with USB bootloader and serial port debugging
Built in 100mA lipoly charger with charging status indicator LED
Reset button
 

HPD13:
Receive current: 10 ~ 14mA
Interface Type: SPI
Operating temperature: -40 ° C to + 85 ° C
Digital RSSI function
Automatic frequency correction
Automatic gain control
Radio wake-up function
Low voltage detection and temperature sensor
Fast wakeup with frequency hopping
Highly configurable packet handlers


 
Document link: http://www.diymalls.com/files/DIY0050-DIY0051-LORA32U4.zip

 

https://drive.google.com/open?id=0B8DSGdAr8_31RkQ0UGo2Nzh1YXM

Package includes:
1 X LoRa32U4 II Lora Module development board

Micro TF SD Card Module
close

Control Interface:
A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin

3.3V regulator circuit:
LDO regulator output 3.3V as level converter chip, Micro SD card supply.

 

   
Model MicroSD Card Adapter v0.9b
Quantity 1
Color Blue
Material PCB
Features Working voltage: VCC 4.5~5.5V; Current: 0.2~200mA; Interface electrical level: 3.3V / 5V; Onboard 3.3V voltage regulator circuit; Supports Micro SD up to 2GB; Micro SDHC up to 32GB; Leads: GND, VCC, MISO, MOSI, SCK, CS; SPI standard interface ; 4 M2 2.2mm screw installation holes
Specification Greatly expands the Arduino memory
Application For your DIY project
English Manual/Spec Yes
Packing List 1 x Board
Control Interface:
A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin

3.3V regulator circuit:
LDO regulator output 3.3V as level converter chip, Micro SD card supply

Level conversion circuit:
Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal

Micro SD card connector:
Since the bomb deck for easy card insertion and removal.

Positioning holes:
4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combinationimensions: 1.81 in x 0.94 in x 0.28 in (4.6 cm x 2.4 cm x 0.7 cm)
Weight: 0.18 oz (5 g)
 

MAX3232 RS232 Serial port to TTL Converter Module with DB9 Connector
close

Description:

  • Weight:16 g
  • Color: as picture show
  • Size:27mmx30mm/1.06"x1.18"(inch) (approx)
  • WorkingVoltage: 3V-5V
  • MAX3232 Chip
  • Pin definition: GND,RXD,TXD,VCC,+5V
  • Pitch:2.54mm
  • Cable:21cm (including 2 ports)
  • Scope of application:
    1. can be used to write all kinds of SCM: such as STM32, NXP, STC, Renesas etc..
    2. the radio, mobile phone brush machine modification, brush XBOX360, GPS, vehicle inspection, brush DVD, hard disk repair, upgrading set-top box.
  • Reminder: 
    When use the plate, must be VCC external 3.3V or 5V power supply, power LED lights on, the module will work! No external power supply, LED lamp is not bright, the module will not work.

  • Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
  •  

FT232RL USB to Serial Adapter Module USB TO UART (Economy)
close

Description:
Use FT232RL chip;
Draw out all signal port of FT232RL chip;
RXD/TXD transceiver communication indicator;
USB power supply, can choose 5V or 3.3V ,set by jumper.
Each module has been tested
Can use for Arduino Pro Min.

 
Package Included: 
1 X FT232RL Module
1 X 6P Pin

PL2303 HX USB to TTL (usb-ttl) RS232 Module Serial Cable
close

 

Description:

Line about 1 m long.

Line sequence definition

Red + 5V

Black  GND

Green  RXD

White  TXD

AV to USB EasyCapture single-channel video capture card
close

EasyCAP USB2.0 Video Adapter with Audio, it capture High quality video and audio file direct by USB2.0 interface without sound card. Solution for laptop, we have enclosed the professional video editing software Ulead Video 8.0 SE DVD then provide best editing function for you. Video is video-editing software that makes editing your movies as fun as shooting them. The new Video Movie Wizard helps novice users finish stylish movies in only three steps. Share finished projects on DVD, tape, the Web, and mobile devices. High-speed rendering and real-time performance mean less time waiting and more time creating. You create many special effect and clip video files etc.The installation is very simple and the external power is unnecessary.

Specification Rev.2.0
Complies With Universal Serial Bus
Supports NTSC, PAL, Video format
Audio input: Stereo audio (RCA)
Video input: One RCA composite, One S-Video
PAL:720*576@25fps
NTSC:720*480@30fps
Supports high quality video resolution

Include Professional and easy to learn & used video editor software: Ulead Video 8.0 SE DVD
Capture Video & Audio though USB 2.0 interface
Popular USB 2.0 interface and not need other power
Support Brightness, Contrast, Hue, and Saturation control
Could capture audio without the sound card
High plug & play
Support For All Formats: record in DVD±R/RW, DVD±VR, and DVD-Video
Applying to internet conference/net meeting
System:Windows 98/ME,Windows 2000  Win7 32/64bit

package:  

1 x 1 Channel USB DVR Video Audio Capture Adapter Easycap 
  1 x CD Driver 
  1 x USB cable

can bus arduino Shield
close

Description: This shield gives the Arduino CAN-Bus capability. It uses the Microchip MCP2515 CAN controller with MCP2551 CAN transceiver. CAN connection is via a standard 9-way sub-D for use with OBD-II cable. Ideal for automative CAN application. The shield also has a uSD card holder, serial LCD connector and connector for an EM406 GPS module. Making this shield ideal for data logging application.

  • Cable not included
  • View the related products for a recommended cable to use with this board

Note: This product is a collaboration with SK Pang Electronics. A portion of each sales goes back to them for product support and continued development.

Features

  • CAN v2.0B upto 1 Mb/s
  • High speed SPI Interface (10 MHz)
  • Standard and extened data and remote frames
  • CAN connection via standard 9-way sub-D connector
  • Power can supply to Arduino by sub-D via resettable fuse and reverse polarity protection.
  • Socket for EM406 GPS module
  • Micro SD card holder
  • Connector for serial LCD
  • Reset button
  • Joystick control menu navigation control
  • Two LED indicator

Documents: